DPA - 5006-11A
Artnr: IDS0048139
Tarneaeg: Kaup on ajutiselt otsas. Kontakteeruge meiega tarneaja prognoosiks. »
Teave:
A complete surround kit combining three d:dicate™ 4006A Omnidirectional Microphones and two d:dicate™ 4011A Cardioid Microphones, carefully factory-matched to achieve full precision.
Even though the standard tolerances on the d:dicate™ Microphone Series are extremely low, the surround match is even closer.
The specially-selected d:dicate™ 4006A Omnidirectional Microphones are matched within ±0.5 dB on both frequency response and sensitivity. The d:dicate™ 4011A Cardioid Microphones are matched within ±1 dB.
The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (±2 dB) of the microphones make the d:dicate™ 4006A Omnidirectional Microphones the perfect choice for all AB Stereo, Decca Tree or surround main array recordings. The precise reproduction, total transparency and natural-sounding clarity of d:dicate™ 4006A Omnidirectional Microphones will provide you with a lifetime of satisfying listening.
The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone/accessory inlays.
Directional pattern
4006A: Omnidirectional; 4011A: Cardioid
Principle of operation
4006A: Pressure; 4011A: Pressure gradient
Cartridge type
Pre-polarized condenser
Frequency range
10 Hz to 20 kHz
Frequency range, ±2 dB
4006A: 10 Hz to 20 kHz
Frequency range, ±2 dB, at 30 cm (11.8 in)
4011A: 40 Hz to 20 kHz
Sensitivity, nominal, ±2 dB at 250 Hz
4006A: 40 mV/Pa; -28 dB re. 1 V/Pa
Sensitivity, nominal, ±2 dB at 1 kHz
4011A: 10 mV/Pa; -40 dB re. 1 V/Pa
Equivalent noise level, A-weighted
4006A: Typ. 15 dB(A) re. 20 µPa (max. 17 dB(A)). 4011A: Typ. 18 dB(A) re. 20 µPa (max. 20 dB)
Equivalent noise level, ITU-R BS.468-4
4006A: Typ. 27 dB (max. 29 dB). 4011A: Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting)
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL)
4006A: Typ. 79 dB(A). 4011A: Typ. 76 dB(A)
Total harmonic distortion (THD)
< 1% up to 139 dB SPL peak
Dynamic range
4006A: Typ. 124 dB. 4011A: Typ. 121 dB
Max. SPL, peak before clipping
4006A: 147 dB. 4011A: 159 dB
Switchable attenuator, filters etc.
0 dB / -20 dB
Minimum load impedance
2 kΩ
Cable drive capability
100 m (328 ft)
Output balance principle
Impedance balancing with Active Drive
Common mode rejection ratio (CMRR)
> 60 dB
Power supply (for full performance)
48 V Phantom power (± 4 V)
Current consumption
2.8 mA
Connector
XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
Weight
4006A: 163 g (5.7 oz). 4011A: 158 g (5.6 oz)
Microphone diameter
4006A: 16 - 19 mm (0.63 - 0.75 in). 4011A: 19 mm (0.75 in)
Capsule diameter
4006A: 16 mm (0.63 in). 4011A: 19 mm (0.75 in)
Microphone length
170 mm (6.7 in)
Maximum output voltage, RMS
> 5 V
Polarity
+V at pin 2 for positive sound pressure
Temperature range
-40°C to 45°C (-40°F to 113°F)
Relative humidity (RH)
Up to 90%
Matching tolerance (frequency response and sensitivity)
4006A: ±0.5 dB. 4011A: ±1 dB
Phase deviation for kit
4006A: < 5°. 4011A: < 10°
